CHAPTER 5
SWITCH AND
JUMPER SETTING
The Plug and
Play features let hardware configuration for IRQ and I/O address is
detected by BIOS automatically, so that it need not switch and jumper
setting. The on board switch can be used to identify card number by the
users (if you do not set the switch, the PnP BIOS will assign card
number automatically).
JP1,JP2 (Jumper 1,2) Select high speed mode or normal speed mode.
JP3 (Jumper 3) Set RS422 or RS485 for second port.
SW1 (Switch 1)
Identifies card number.
Under the RS485 mode, all the
RS485 Ports are set to receive mode automatically, while one port use
to send data to the other port, it needs to set RTS signal to 1, to
enter driver mode, then send message or data. After sending message, it
needs to set signal to 0 to enter receive mode again.
¡@
1. Select High Speed or Normal Speed Mode
The JP1 is
used to select high-speed mode or normal speed mode of RS232 port, and
JP2 is used to select high-speed mode or normal speed mode of second
port (RS422 or RS485); to select normal speed, please short pin 1 and
2, to select high speed, please short pin 2 and 3. The clock rate is
1.8432MHZ for normal speed mode. The baud rate speed up to 115200. The
clock rate is 7.3728MHZ for high-speed mode. The baud rate speed up to
460K.
Pin
|
Mode
|
Short 1,2
|
Normal Speed
|
Short 2,3
|
High Speed
|
For normal speed mode, the user setting baud rate is the same as RS232 baud rate. We list in the following.
Original
|
RS232 on board baud rate
|
50
|
50
|
300
|
300
|
600
|
600
|
1200
|
1200
|
2400
|
2400
|
4800
|
4800
|
9600
|
9600
|
19.2K
|
19.2K
|
38.4K
|
38.4K
|
57.6K
|
57.6K
|
115.2K
|
115.2K
|
For high-speed mode, the user
setting baud rate maps to on board RS232 baud rate are list in the
following. Please note that, you device driver may report original baud
rate, however the speed of communication line is quadruple speed.
Original
|
RS232 on board baud rate
|
50
|
200
|
300
|
1200
|
600
|
2400
|
1200
|
4800
|
2400
|
9600
|
4800
|
19.2K |
9600
|
38.4K |
19.2K
|
76.8K
|
38.4K
|
153.6K
|
57.6K
|
230.4K
|
115.2K
|
460.8K
|
2. Set RS422 or RS485 Mode for Second Port
The
JP3 is used to set RS422 or RS485 mode for second port, to short pin 1
and pin 2 means set RS422 mode, to short pin 2 and pin 3 means set
RS485 mode.
Pin
|
Mode
|
Short 1,2
|
RS422
|
Short 2,3
|
RS485
|
3. Card Identifier
The switch is used to identify card number, default setting is card 15 , and there are two methods to set the card number:
PnP mode
Just plug in PCI BUS 4 CHANNELS RELAY OUTPUT / 4 CHANNES PHOTO ISOLATOR INPUT ADAPTER into PCI slot, the PCI BIOS will allocate I/O address to each adapter automatically and assign card number start from 0 to each adapter. You may set any card number at PnP mode, and you need use software tools to distinguish port id. Almost all of the operating systems run at PnP mode.
manual mode
Set card number by card identifier switch, the PCI BIOS will assign pre-allocated I/O address to each adapter. Please set different card number to each adapter (do not duplicate card number setting).
¡EThe card number starts from 0 to 15.
|